How to Cut a 60 Degree Bevel on a Table Saw

Dynamics of a Table Saw

Before getting into the procedure of cutting a 60 Degree Bevel on a Table Saw, let us gain a little knowledge about the tool we will be working with.

A Table Saw is a mechanical tool, commonly used for segmentation during woodwork. The main feature of the Table Saw is the circular saw blade it consists of.

The Circular blade extends out from the top of the table, providing tightness to the wood piece. This helps in preventing the piece from rocking. The Table Saw works through a motor. It turns on and becomes active once the power is supplied with electricity.

Structure of a Bevel Cut

A Bevel Cut is basically a type of cut that results in providing sharp edges to the wood. These sharp edges are unequal to the upper area of the wood. The formation of cut is in a beveled curve. The profile of the Beveled curve is round. Therefore, it has a radius.

A Bevel Cut is known through a lot of names. These names include slope cut, angled cut, incline cut, cant cut, and a slant cut.

The measurement of the angle maintained while making this type of cut is calculated opposite to the square-edge cut. A Bevel Cut can be obtained by placing the blade against the vertical plane. The angle of the cut must consider showing off the sharp ends of the piece.

Uses of a Bevel Cut

In Carpentry, Bevel Cuts are commonly used to create pieces of wood that are smaller in size. The small size of the cut provides protection from weathering and is also aesthetically appealing to the eyes. However, the use of a Bevel Cut is not restricted to small-sized woodwork.

The process which allows the wood to soften from the end edge also requires Bevel Cuts. Furthermore, the use of Bevel Cuts extends in the concealing of the joints made within different pieces of wood.

The procedure of hiding the points require the joints to slightly overlap each other, resulting in a single piece. You can acquire this harmonious angle by joining the pieces together with the edge. The Bevel cuts are not straight-edged cuts most of the time.

Cutting a 60 Degree Bevel Using a Table Saw

When it comes to measuring and cutting angles using a Table Saw. The process is quite straightforward and not that tricky. The procedure requires a thorough understanding before you actually get into it. A firm understanding of what needs to be is the key.

The main concern working with a Table Saw is that it’s only capable of opening its jaw to a 45-degree angle.

A 60 Degree Bevel cut, is more than 45 degrees. The process of reaching the height of a 60-degree angle will require you to make some necessary adjustments. To execute a 60-degree Bevel Cut, through a Table Saw you can follow the guidelines below.

Calculating the Right Angle

The first step to attain a 60-degree Bevel Cut will require you to identify the appropriate degree of angle. To attain that, you will need to do some math.

The trick is simple, you will have to subtract 45 from the final angle. In this case, our target is to acquire a 60-degree Bevel Cut. To attain that degree of Bevel Cut, you will have to set an angle of 15 degrees. As, 60-45= 15.

Adjusting to the Desired Angle

The Table Saw comes with a knob. The function of that knob is to make adjustments. Adjust the knob, till you reach the desired angle on the Table Saw. As mentioned above, in this case, the right angle would be 15 degrees, which you will need to adjust perfectly.

Placement of the Wood

The Placement of the wood will determine the kind of cut you are looking for. Placing the wood vertically on the Table Saw will be your next step. Make use of another scrap wood piece. Moving on with it, simply put the scrap piece next to the main wood piece.

It is important to adjust the wood in the correct position. To execute the cut accurately, ensure that the placement of the wood is opposite to the blade.

Increasing the Blade Angle

At this point, you will need to heighten the blade, enlarging the angle. By increasing the height of the blade, you will be able to cut the wood at a greater angle.

The Spinning handle/knob will assist you in adjusting the height. You can find the Spinning handle/knob located in front of the Table Saw.

Proceeding with the Cut

Before turning the machine on, make sure that everything is in the correct order. Now, turn on the machine and execute this step by making the cut. In this part, you will have to hold on to the wood piece firmly, making use of both hands. Therefore, it is better to use clamps if available, for accurate results.

Note that, too much force during this point will result in uneven cuts. Hence, it is better not to exert force with a lot of pressure.

Handling Uneven Bevels

The most accurate calculations can surprisingly lead to uneven Bevel Cuts. It is quite common and occurs due to the presence of thin wood fins. You can remove the fine wood fins by making use of a tiny trimming plane.

You can start off with the removal of those wood fins with the little blades. However, you can increase the exposure of the blade to the remaining parts as you go further.

BOSCH 10 In. Worksite Table Saw With Gravity-Rise Wheeled Stand


Dimensions: 27 x 32.5 x 13 Inches
Weight: 109 Pounds
Speed: 3650 RPM
Includes: 4100 10 In. Worksite Table Saw, Gravity-Rise Table Saw Stand, Rear Outfeed, 10 in. Carbide-Tipped Blade, SquareLock Rip Fence, Auxiliary Fence for Narrow Workpieces, Miter Gauge, Smart Guard System, Push Stick, Throat Plate Insert, Multi-Function Blade Wrench, Adjustment Wrench

Check Price


The technique discussed in this guide will cater to all your queries regarding the execution of a 60-degree Bevel Cut through a Table Saw. Furthermore, you can make cuts of any desired degree by applying the same method discussed here.

The Bevel Cut has more to do with the identification of the right angle and making the correct mathematical calculations. The adjustments based on the calculations will enable you to make the perfect Bevel Cut.

Leave a Comment

Share via
Copy link
Powered by Social Snap