How to Drill Into Brick Without a Hammer Drill?

You will have to use other types of drills for better results. You can either use the masonry or the impact driver. Power drill and the Tungsten drill bit are also handy while drilling the brick.

This guide will help you understand how to drill a brick without a hammer drill.

The Tools Required

You will need a masonry drill bit and its sharpener along with a power drill. Water is also very essential, along with some safety equipment. You might also require a hammer and other drill bits for the process.

Once you get hold of all these tools, you will have to fit the bits into your power tool. You will have to keep the bit in the position wherein you want to drill.

Mark the Center

After you position the bit in the place where you want to make a hole, you must make a mark before you start drilling. You can do this by making a mark with a pencil or pen. This will prevent confusion at the time of drilling.

Drilling the hard brick at the wrong place might be troublesome, which is why this is an integral part before moving forward with the actual drilling process.

Fit the Drill Bits

A majority of the drill bits will not be able to work through the hard brick. This is you need to fit a tungsten carbide masonry drill. These drill bits are much tougher than the others, and their tips are also hard enough to complete the task.

There is a considerable possibility of the other drill bits getting ruined due to the bricks. Hence, the masonry drills use intense force, which does not allow them to get blunt halfway through.

However, you might want to keep a few more extra drills to be on the safe side. Hence, before you decide on any drill bit, you should check the quality and how powerful it is to cut through the hard brick.

Otherwise, the work may be left incomplete and, at the same time, will end up making the bits very blunt as well.

Drill Large Holes

Before moving forward with the drilling process, you can start by using a pilot drill. This will allow the drilling more preciseness, and you can begin by following the previous mark since it becomes difficult to see the mark with a bigger hole and might end up being less precise.

After that, you can slowly increase the holes’ size as the process itself starts getting more manageable. However, you might need to make many drills in terms of its diameter to get the hole’s exact size.

Diamond core drills are also beneficial in giving precise results concerning the size hole. The cuts are relatively clean with these drills. It can cut through any material, and there is no difficulty in drilling a brick.

Use Water Consistently

Since the drill bits are of much higher quality and the work provided is also intense, the heat generated is a lot. The tips of the drills tend to get hot and will burn more quickly. This is why the bits get blunt very soon.

To avoid burning out the drill bits’ tip resulting in them being blunt, you must use water consistently to keep it cool. The water can be supplied from the pipe or the direct source.

Another way of cooling down the drill bits with water is by constantly dipping the tip of the drill in a container full of water.

The Dust and Debris Should Be Cleared

Along with cooling down the drill bits with a lot of water, you should clean the debris. The cleaning process will make it a lot easier to drill the hole and prevent burning the tip as well. This is an important step, especially if you are not using a hammer drill.

Moreover, using a vacuum might also be easy in cleaning the dust out so that the results are much more prominent. It should be noted that you should be wearing a mask and other safety equipment while doing the tasks.

How to Drill

Most people don’t know how to drill into brick without a hammer drill. Using the tools mentioned above will make the tasks much easier, especially if the drill bits are suitable materials.

When you start to drill the brick, you will have to drill the mortar first. This is comparatively the softer material of the brick and much easier to drill. If this is drilled in the beginning, there are lesser chances of the bricks cracking as well.

To make things easier, you might want to mark the holes in the beginning in the mortar joints themselves. This allows you to start drilling holes more precisely at the soft parts of the brick as well.


It isn’t challenging to drill into the brick even if you don’t have the right equipment like the hammer drill. There are many other drill bits and methods that will help you drill the holes just the way you want it.

Hence, following the required steps and getting hold of premium drill bits will make the task a lot easier than expected.

DEWALT Masonry Drill Bit Set


Material: Carbide
Dimensions: 7.75 x 6.63 x 0.5 Inches
Shank Type: 3-Flat
Tool Flute Type: Spiral
Pieces: 7
Ideal for Drilling Holes in: Brick, Block, Concrete & Masonry

Check Price

DEWALT 20V Max Cordless Drill


Voltage: 20 Volts
Dimensions: 13.88 x 9.88 x 4.25 Inches
Weight: 3.64 Pounds
Speed: 0-450 & 1,500 RPM
Power Source: Battery Powered
Perks: Warranty, Compact & Lightweight Design, Ergonomic Handle, 2 Speeds

Check Price

DEWALT Hammer Drill


Voltage: 120 Volts
Dimensions: 10.5 x 14.44 x 3.25 Inches
Weight: 6 Pounds
Motor: 10 Amp
Power Source: Corded Electric
Perks: Warranty, Dual Mode, 2-Speed Range, 50% More Power, Durable & Reliable

Check Price

Leave a Comment

Share via
Copy link
Powered by Social Snap