How to Install Peel and Stick Tile on Plywood: a Step-Wise Guide

Are you planning to bring about a new look on your floors? What if someone told you that you could revamp it completely without digging out the previous setup?

The reason manufacturers have started to produce more and more peel and stick tiles is for your convenience! It is, very merely stating, a peel and stick process to renovate your floor design. If you manage to install them successfully, your floors will be safer and more resilient than ever!

So, the question begs itself, how to install peel and stick tile on plywood? In this article, you will get your hands on the simple application of these low-maintenance vinyl tiles.


Is Plywood a Good Combination Base for Peel and Stick Tiles?

With peel and stick tiles, you do not have to worry about the adhesive bond spilling all over. These tiles already come with a sheet of glue on the backside. Once you peel it off, you can quickly and smoothly paste it on the base surface.

If you have plywood as your base from earlier, know that these will bond effortlessly with it. That said, you must ensure that your floor is cleaned correctly, even if it is just bare plywood.

Either way, you would be glad to learn that plywood offers a smooth underlayment for such types of tiles. Since it is reasonably porous in nature and texture, certain plywood work best as opposed to others.

All you need to keep in mind is that a minimum of 1/4-inch-thick plywood serves suitably for the purpose. As a result, you will have evenly laid-out flat tiles.


How to Install Peel and Stick Tile on Plywood in Four Easy Steps

As you may have gathered from the sections mentioned above, peel and stick tiles make your life convenient. So, let us dive into a detailed procedure of how to get the task done.

Follow the below-mentioned steps to lay your floors with the resilient and low-maintenance tiles you have always wanted!

Step 1: Secure the Plywood

You cannot successfully achieve your goal if you do not have the very base of plywood installed in the first place. So, incorporate this step in your procedure if you are installing plywood for the first time.

On the other hand, if you have already prepared the floor with the base, you can skip to the next step.

So, the best way to go about it is to fasten the plywood with some galvanized screws. Follow the process of countersinking the heads of all the screws next. Remember that if you have loose areas of the plywood subfloor, it can lead the peel-and-stick tiles to hoist up with time.

How Do You Figure Out if There Is Any Loose Plywood?

The solution is a relatively simpler one. Take a walk across the floor, and you will be able to feel the hardness. In case some sheets feel soft to your foot, you need to secure them further.

If you feel like a few edges between the sheets might be uneven, correct the error by adding screws. That will help you to pull up the superimposing sheet down, thereby aligning it with the others. However, if you still think that it has not aided your problem, try using coarse sandpaper.

If that doesn’t work, sand the edge with coarse sandpaper. Another pointer you must keep in mind is that water clogging usually swells up the plywood in damp areas. For example, you will need to check the condition of the bathrooms or wash areas occasionally.

If you find such discrepancies, make sure to correct them whenever necessary.

Step 2: Cleaning the Plywood

Regardless of the time since you last installed your plywood base, cleaning it up is a necessary step.

As mentioned before, inconsistencies in the levels can make your floor messy. The whole point of aesthetic peel and stick tiles will be left defeated. To avoid that, run the surface with sandpaper when you think it is necessary.

Alternatively, you could run your foot over the floor to check for bumps. These can be fixed with extra screws. However, even after you have cleaned the plywood on the said level, you may have to dig a little deeper.

This means that just vacuum or brush over the surface before finally moving on to the determining steps. Any particles or dust that sticks between the plywood and tiles will lead to problems in the future.

Step 3: Applying a Layer of Primer

Just like the case of paint, the role of latex primer is to seal the plywood up. You will notice that the peel-and-stick tiles attach better with it. However, before spreading a layer of the primer, you need to spill some floor-leveling compound evenly. It will tone out any seams and depressions.

If you find excess fluid over some areas, try to scrape it off using a putty knife. Remember that the compound is simply a cement base that becomes pasty after you add water to it.

After drying

When it dries completely, vacuum the floor to get rid of all the grit and dirt particles. Now comes the time for priming. You want to mix the primer with water in the proportion of 3:1.

Adding water to it will make sure that the primer seeps deep into the plywood.

The next layer should be a full-strength coat of the primer. These two layers should be more than enough to hold the tiles and plywood together.

Step 4: Install Peel and Stick Tile on Plywood

Since there is a variety of peel-and-stick tiles available in the market today, you should scrutinize yours. Note that while some of them are rubbery and flexible, the others could be rigid.

Ideally, it would be best to let them lay in the room for at least 24 hours before fixing them. It will settle the temperature gap between the two. Moreover, it should help you mark off the floor. You will get a clearer idea of intersections and symmetry.

After you have primed your plywood floor, peel off the sheet covering the tile’s adhesive on the back. Remember to be careful and even with the peel. You would have to buy a new tile if you rip the paper with the adhesive, so do not be too aggressive.

Simultaneously, if you leave out a tiny patch of the covering sheet on, the tile will not stick evenly.  Use tools like a flat putty knife or the edges of a giant metal tray to run over the paste later on.

Step 5: Rolling the Tiles

The final step to finish off the process is rolling over the floor with a 75 to 100-pound roller. It will help keep each tile stick to the primer and the plywood just like magic. You might not see the point of it at the moment.

However, if you skip this part, the side effects might start to show in a few years. So, if you want to keep the life of your floor long and lively, finish it off with some rolling.


Final Thoughts

How to install peel and stick tile on plywood is not as big as it may seem. If you follow the steps mentioned earlier, nobody can stop you from having a magnificent floor.  Lastly, do not forget to take the bits of precautions either!

Leave a Comment

Creative Commons License
Woodsybond.com by https://www.woodsybond.com is licensed under a Creative Commons Attribution-NoDerivatives 4.0 International License.
Share via
Copy link
Powered by Social Snap