How to Nail Baseboards With Hammer

Your apartment is your place to show your creativity. You can add a character to your unadorned apartment in numerous ways. But, one simplest method is by installing the baseboards at the foot.

Though it seems you need an architect to install such a thing, you can do it on your own with a hammer. You can get all the tools from your local hardware store to cut and then install the baseboards in your home. Moreover, you don’t even need a nail gun.

You will save a lot of money when you nail the baseboard using a hammer. If you want to transform the appearance of your home, learn how to nail baseboards with hammer in this article.


Tools Required to Install the Baseboard

You will require the below-mentioned tools to nail the baseboard. Most of the tools are readily available at home or in a local hardware store.

  • Nail set
  • Hammer
  • Hack Saw
  • Latex sealant
  • Finishing Nails


How to Nail Baseboards With Hammer – Step-by-Step Process

People usually overlook the importance of attaching baseboards to the walls. This is because they assume that the corners are intended at certain angles, and there are straight walls. That is not true.

When you install the baseboard, you will know that your walls are actually bowed in certain places, and you will notice the odd angles. So, a good nailing job of the baseboards helps you get a finished look on your walls.

Let’s discuss how to nail baseboards with hammer in this step-by-step guide.

Step 1: Measure and Cut the Baseboards

Your first step is the accurately measure the baseboards and cut in the required dimensions. Keep the baseboards that meet outside the corner some inches longer compared to the wall so that it becomes easy to make cuts using a hack saw.

Mark the same number on the wall as well as on the back of the baseboards. Now, mark and find the studs in the wall so that they can make a solid base for baseboard nailing.

Step 2: Establishing the Height of the Baseboard

You need to establish the height of the baseboard so that the floor is on the level. To check the floor level, set the baseboard on a four-foot level on the floor adjacent to the wall. If it is not at the required level, you should find the lowest point of the floor. Take a small piece of the baseboard and tack it in the wall along with the nail at this point.

You can create a horizontal mark after every few feet on the wall. Now, take a chalk line and mark it along the room’s perimeter to determine where the baseboards will land upon installation.

Hold the first baseboard at the inside corner of the wall and secure it with a nail. Now set the compass between either of the top corners of the board and chalk line to span the vertical distance.

Step 3: Scribing for Tight Fit

Do not change the position of the compass as you measured in the previous step. Keep the point on the floor and pencil against the baseboard. Now, align the points vertically by sliding the compass on the floor, covering the length of the board.

After that, you need to cut along the scribe line with a circular saw that is set for a two to five-degree bevel level. Now, you can use a block plane to trim the beveled edge towards the line. Lastly, put the scribed baseboard on the wall. This way, the edge should be in line with the chalk line you marked in Step 2.

Step 4: Using Hammer to Nail the Baseboard to the Wall

Place the scribed baseboard against the wall to nail it. It becomes easy to hammer when your nails are angles downward rather than hammering the nails straight into the wall.

You should make strong and solid whacks instead of tiny hits to prevent dents on your baseboard. However, this comes with practice, but you should be confident enough to use the hammer. Stop the hammer when the nail is 1/8 inch outside the wall.

Step 5: Use a Nail Set to Further Drive the Nails Inside the Wall

If you use a hammer to drive nails straight into the walls, it could result in a hammer-shaped dent. That’s where the nail set comes to the rescue. You can place the tip of the nail set on the nails top. Besides, the nail sets are available in a different size; you would want a nail set slightly smaller in comparison to the nailhead.

Use the nail set to drive the nail completely inside the wall. If you are unsure how to do it, try practising it on a spare piece of wood until you are able to do it. Now, do it on the baseboard and drive it just beneath the baseboard surface.

Step 6: Use Sealant for the Finish

You can use caulk or outdoor/indoor sealant to fill the gaps between the wall and the baseboard. The best way to fill the gaps is by using your finger. After applying the sealant, you can slide your finger over the top of the baseboard to smoothen the surface.

You should wipe off the excess sealant by using a paper towel.

Step 7: Covering the Nail Heads

Nailheads may be visible on your baseboards but, you can easily make them invisible. For that, put a small amount of sealant on the top of the nail heads and let them dry.

The process becomes even smoother if you use a white sealant and white baseboards, as both will blend together flawlessly. For different colors, such as natural wood baseboards, you need to find matching paint.

Estwing Hammer

Specifications:

Material: Solid American Steel
Dimensions: 13 x 5 x 1 Inches
Weight: 13 Ounces
Claw: Curved With Smooth Face & Shock Reduction Grip
Perks: Forged in One Piece, Patented Shock Reduction Grip, Made in the USA

Check Price


Safety Considerations

Every woodworking projects have some risks or others. Therefore, you need to keep in mind some safety precautions while working with a hammer and nails.

  • Wear hearing protection and safety glasses when you are using a nail set and hammer.
  • Wear a glove on the hand in which you will hold the nail set. If you happen to strike something on your hand, the gloves will protect your hand from the impact.
  • When the nail sets have become dull and lost their pointedness and round shape, either use them for other task or discard them.
  • Hold the hammer properly around the handle and use it by lightly swinging it in your hand. Do not hold it around the neck, as it can be risky.

Final Thoughts

How to Nail Baseboards with Hammer? The process is similar to that of a nail gun, but you will have to buy nails designed to use a hammer. Also, you will need a different size of nail sets so that you can effectively insert the nails into the wall.

Only the planning and measuring phase of the baseboard requires your time and effort; the actual installation with the hammer and nails takes no time. Thus, you can be your own architect to transform your home as you want.

Leave a Comment

Creative Commons License
Woodsybond.com by https://www.woodsybond.com is licensed under a Creative Commons Attribution-NoDerivatives 4.0 International License.
Share via
Copy link
Powered by Social Snap