How to Put Sandpaper on a Sander

Sanding is one of the most important parts of the woodwork to make your wood piece smooth and shiny. However, inexperienced woodworkers often find themselves wondering how they can put sandpaper on a sander. If you are in the same dilemma, then do not worry. Usually, it is not as hard as you think.

You can find a broad range of sandpapers with each of them offering a different and unique effect. After all, it is a common practice to change the grade of sandpaper during a project. Depending on your project, coarse sandpaper may be used to smoothen the rough surfaces. And to finish the project, a grit paper may be required for that smooth and high sheen look.

Depending on the applicator, the shape of the sandpaper may also be different. Some are circular, while others, might be rectangular. So these are just a couple of things you first need to know.

So if you want to replace the sandpaper on a sander, how can it be done? Let’s find out.


Sandpaper Replacement

Step 1: Raise the Front Clamp

Usually, sanders have two clamps; with one located at the front and the other at the rear. These clamps are often operated with springs. To remove the old paper, what you must do first is to release the front clamp. After that, grab the new paper and place it on to the clamp until it’s fully adjusted with the spring posts. Although keep in mind that it should be placed evenly on the mounting plate.

Step 2: Fold Paper

To eliminate the slack, you need to fold the paper underneath the clamp and tighten the plate as much as possible.

Step 3: Back Clamp Release

After securing the front clamp, you can now tighten the back clamp to restore the slack.

Step 4: Secure Back

Now under the clamp and the plate, make sure that the end of the paper is folded tightly and then firmly press it down.

If you have properly followed the steps mentioned above, then congratulations because your job is done.


Power Sander

If you want to replace the sheet of a power sander, then the process is far easier. In fact, it also provides much more flexibility in managing the ¼ sheet sandpaper.

Step 1: Open the Clamp

Always properly disconnect the sander from the power source before placing new sandpaper onto it. Open the sander and evenly place the paper and then clamp it down.

Step 2: Bend Paper

The fed end of the paper needs to be inserted at the other side of the sander. To do so, bend it is as tight as you can.

Step 3: Stretch Paper

For this part, you must ensure two things; first is to push the paper as far as possible in the sander, and second, make it as tight as possible. As long as you are able to make the paper as tight as it can be, you shouldn’t face any problems with the process.


Why Is Sanding Important?

Now that you have learned how to put sandpaper on a sander, for the beginner woodworkers out there, you may have a question in mind. Why is sanding important, to begin with? While we did roughly go over how sanding can give the surface of the wood that smooth shine, there are many more benefits it offers as well.

While professional woodworkers may have their own preferences with sanding, all of them are going to agree with one thing; its importance. Sanding is undoubtedly one of the most important parts of the woodwork. This could apply even more if you are a person who always has an eye out for aesthetics.

Let’s see some of the major benefits of sanding your wood piece:

1. Fixing Imperfections

During the process of woodworking, the wood may go through a lot of wear and tear. The chances are that by the time you are done, it is covered with dust, dirt and scratches. The most important aspect of the woodwork for most woodworkers is to make sure that their craftsmanship looks as aesthetically appealing as possible. This is the reason they often prioritise sanding so much.

2. Desired Look

Have a look in mind that you would like to give to your wood piece? Well, sanding will allow you that. With sanding, the pores of the wood piece are opened, thus, enabling you to attain that desired look.

3. Avoiding Chemical Stripping

Some people may argue that why not simply go for chemical stripping? The answer for that is simple, it does not give the level of perfection that a woodworker would want for their wood piece. If you want to remove all the remaining finish, then sanding is the only way to do so.


The Bottom Line

Sanding surely has its place in the world of woodwork. If you are just starting out, then you might face some difficulties wrapping your head around all this. However, do not worry because learning how to put sandpaper on a sander is one of the first steps of becoming a woodworking master. So, we wish you the best of luck for your future woodworking projects! Make them smooth and glossy by using the right sandpaper.

Leave a Comment

Creative Commons License
Woodsybond.com by https://www.woodsybond.com is licensed under a Creative Commons Attribution-NoDerivatives 4.0 International License.
Share via
Copy link
Powered by Social Snap