How to Seal Laminate Flooring Seams

It goes without saying that choosing the right flooring is one of the biggest decisions you’ll make when it comes to the aesthetic appearance of your house. With a plethora of flooring options, over the years laminate floorings have become a top choice. Perhaps it is due to how looks like wood, while at the same time, and is lighter on the pocket in comparison to timber flooring.

With that said, although laminate floorings are quite attractive. If you’re cutting costs, then you might as well be prepared to compromise on the quality. Over time, it is easy for laminate flooring to get damaged and worn out. Thus, it’s crucial to take any step you can to protect it.

When speaking of protecting laminate floorings, the question arises that is important to seal them. The short answer is yes. However, it isn’t as easy as it sounds. You might be able to buy sealers online to get started, but without knowing the right steps, you might damage your floorings.

If you seal laminate flooring seams the right way, then they can offer greater durability and in general, become more resilient to regular wear and tear.

Thus, this article will cover the ins and outs of not only on how to seal laminate flooring seams but the flooring as a whole. Along with it, we’ll look at some pros and cons of doing so.


Pros of Sealing Laminate Flooring

  • Enhances durability and makes the flooring long-lasting.
  • Helps to avoid subfloor damage in rooms with higher moisture level like kitchen and bathrooms.
  • Laminate flooring sealant is cheap.
  • Easy to apply and can be carried out as a DIY project.

Cons of Sealing Laminate Flooring

  • Sealing products may not work on all laminate flooring brands.
  • Sealing products may make the laminate flooring more slippery. Thus, promoting risks of injury.
  • Applying a sealant to laminate flooring may end its warranty, especially if it isn’t recommended by the manufacturer.

Materials Needed

  • Type II glue (minimum)
  • Caulk gun
  • Putty knife
  • Brush
  • Paint roller (optional)
  • Straight prybar

The Right Way of Sealing Laminate Floorings

Step 1: Read Instructions

The sealant you purchase will always come with detailed instructions. Make sure to read them as they will provide insight on how to pre-clean your laminate flooring. Along with other necessary information to flawlessly get the job done.

Step 2: Remove Baseboards

Make sure that the baseboards are carefully removed. Most people rush this and end up breaking them. If you plan to use the same baseboards later then you want to take things slow. In case there’s paint on the baseboards, you’ll need a knife to cut it.

After that, use the straight prybar to rip the baseboard away. Apply gentle pressure and once removed, mark the area so it’s easier to determine where you need to reinstall it.

Step 3: Use the Sealant

Now that you’ve laid or better yet, removed the groundwork, it’s time for the sealant to come into action. Use a small brush to apply the sealant to the floor. Cover the whole area where the baseboard will be installed and about ¼ out of it as well.

Repeat this step until you’ve done it all over the room. Take extra care while sealing the areas around the bathroom and kitchen. As excessive moisture may damage the laminate flooring if you’re not careful.

Step 4: Sealing the Seams

Sealing the seams would be a bit trickier. However, that too can be done with the help of a smaller brush. The narrower the brush the easier it would be for you. Also, plan out where you’d want to start and finish to avoid confusions.

Take this step as slowly as possible, as you only need to make a thin line with the sealant to cover the seams.

Step 5: Wait for Sealant to Dry

It may take a while for the sealant to dry, depending on its brand. Usually, the manufacturers of the sealant mention it on the packaging or either the instructions. Thus, wait until the given time before you proceed to reinstall the baseboards.

Step 6: Replace Baseboard

Once the sealant is dried, pickup your baseboards to reinstall them. However, it’s recommended to use new nails as there’s a great chance the old ones may have bent during removal.

Step 7: Final Touch

To hide the “evidence” that the baseboards were removed, to begin with, putty the nail holes. After that, simply put some fresh paint on the boards and you’re ready to go.


Cost of Laminate Flooring Sealants

The cost may generally vary depending on the size of the sealant and your overall requirements. However, even the highest quality sealants can be found for under $15. And if you don’t have to pay anyone for the job, then it isn’t a bad bargain. You’ll easily seal the laminate flooring seams for almost nothing.


The Bottom Line

In general, sealing laminate flooring and its seams is generally a very straightforward process. It only takes more or less a few hours. Thus, you can easily take out some time during the weekends to get the job done.

So if you were planning on making sealing the laminate flooring seams a DIY project, then we now hope you’ll easily be able to get the job done.

Leave a Comment

Creative Commons License
Woodsybond.com by https://www.woodsybond.com is licensed under a Creative Commons Attribution-NoDerivatives 4.0 International License.
Share via
Copy link
Powered by Social Snap